NTS-6 Motorized Rotating Friction Torque Tester

Motorized Rotating Friction Torque Tester

Standard Features

Selectable units lbf-in, Kgf-cm, mN-m or N-m (except oz models)
Peak, Real Time and Continuous Output modes (selectable)
RS-232C output
Both CW and CCW operation
Programmable high/low setpoints for Go/No Go testing

NTS-6 Motorized Rotating Friction Torque Tester tests the smoothness of rotation and components of small precision motors, such as, gearbox, bearings, oil seals, etc. The motorized tester turns at a set rotational speed based upon the model. See the specifications table for more details. The tester can be used to measure torque in CW and CCW directions.

The NTS-6 has three modes of operation: real time, PP (peak) and PD (continuous output).

The NTS-6 torque tester has programmable high/low setpoints to enable go/no-go testing. 3 indicator lights inform the user where the current torque reading is in relation the the setpoints. YELLOW lights up for measurements less than Low setpoint, GREEN for between High and Low setpoints, and RED for over High setpoint and testing automatically stops.

SPC Capable

Torque data can be continuously output through the USB virtual COM port enabling you to display a torque profile using data acquisition software. Use the special SW-1SV-USB-NTS spreadsheet to create a torque profile.

All new NTS-6 testers include a free 3 Point Calibration Certificate traceable to NIST. ISO-17025 Certificates are available at an extra charge. NTS-6 testers are sold as a kit and include torque tester display unit, torque detector, Phillips tip, cable and AC power cord.

Ranges

NTS-6 Ranges

Accuracy: ±1% F.S., ±1LSD
Note: oz models do not have selectable units
More Ranges ►

Model			Capacity			Max Speed (no-load)	Bit Size
	ozf-in	lbf-in	Kgf-cm	mN-m	N-m	rpm
NTS-6-S1oz	0.30 ~14.00	—	—	—	—	85	4mm
NTS-6-S2oz	0.30 ~ 28.00	—	—	—	—	25	4mm
NTS-6-S5oz	3.0 ~ 70.0	—	—	—	—	13	4mm
NTS-6-S1	—	0.030 ~ 0.900	0.030 ~ 1.000	3.0 ~ 100.0	—	85	4mm
NTS-6-S2	—	0.030 ~ 1.740	0.030 ~ 2.000	3.0 ~200.0	—	25	4mm
NTS-6-S5	—	0.30 ~ 4.50	0.30 ~ 5.00	—	0.030 ~ 0.500	13	4mm
NTS-6-S10	—	0.30 ~ 9.00	0.30 ~ 10.00	—	0.030 ~ 1.000	18	6.35mm HEX
NTS-6-S20	—	0.30 ~ 17.40	0.30 ~ 20.00	—	0.030 ~ 2.000	18	6.35mm HEX
NTS-6-S50	—	0.30 ~ 45.00	0.30 ~ 50.00	—	0.030 ~ 5.000	5	6.35mm HEX

Specifications

NTS-6 Specifications

Model	S1/1oz	S2/2oz	S5/5oz	S10	S20	S50
Fixed Speed (no-load)	85rpm	25rpm	13rpm	18rpm	18rpm	5rpm
Dimensions (detector)	28mm dia. × 155mm		37mm dia. × 195mm	40mm dia. x 235mm		55mm dia. x 285mm
Bit size	4mm dia.		4mm dia.	6.35mm HEX
Display	4 digit LCD display
Operation	Both CW and CCW motorized rotation
Measuring modes	PP: Peak Mode displays PEAK torque value that will not change until a higher value is measured. GO: Real Time Mode displays TRANSIENT torque values. RG: Output Torque Data every 1/100 seconds.
Measurement start time	Can be set up to 1 second in 0.1 second increments.
Measuring time	Time can be programmed between 1 and 20 seconds.
Go/No go testing	Programmable High and Low values; Green lamp (OK solid, NG blinking).
External input/output	Signal output (open collector): Go and No Go Data output: RS-232C (9600 baud) External start switch input
Power supply	AC100V~240V
Dimensions (indicator)	165mm W × 110mm D × 58mm H

Dimensions

NTS-6 Motorized Rotating Friction Torque Tester Dimensions